Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
Just how do you feel with regards to How to Install a Bathtub Yourself?
Installing a bathtub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is readily accessible, the task can move rapidly; if you have to open up a wall surface to eliminate the old tub and also position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the task and fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to think about utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you set up a new tub in your bathroom if you have currently acquired a new bathtub and also don't need to transform the arrangement of your previous water system pipelines.
Your devices and material checklist ought to make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Protect the tap in place with the producer offered backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub till the level reads degree.
To mount taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water and also inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the bathtub as well as likewise inspect the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the tub has been used a minimum of once as this will resolve it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, resulting in complications with wetness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealant can split relatively early if you do not think about this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece on Tools You Need to Install a New Bathtub while doing a lookup on the search engines. Those who appreciated our blog post please be sure to pass it around. Thanks so much for your time invested reading it.
Need help? Call. Report this page